How To Set Up A Genie Garage Door Opener

Programming Homelink® to Genie® Garage Door Openers

Helpful Tips

When programming, it helps to clear out your HomeLink by pressing and holding the first and third buttons down until the indicator on the HomeLink blinks wearisome so fast (about twenty seconds), then release both buttons. If in that location is something already programmed to your HomeLink do not clear it unless yous are able to reprogram what is already on at that place.

First, Use this process to railroad train the HomeLink device for the following Genie Intellicode® remotes shown below

*If the remote you are using is non shown or this process does not work, run across the next department for additional options.

​

NOTES:  1) Choose an unused button on the HomeLink device that volition be used to open the door.  two) Concord the transmitter  2 inches abroad from the HomeLink device. iii) To clear the HomeLink device completely, see the terminate of the instruction.

1. Printing and concord down any push button on the remote AND press and hold down the chosen push button on the HomeLink device AT THE SAME TIME. The HomeLink indicator LED blinks boring at get-go and and then modify to a faster blink rate - once the glimmer rate changes to fast (could take upwards to xx seconds) – and so release both buttons.  Before you go along, brand certain the HomeLink device indicator has stopped blinking completely.

2. When the HomeLink device indicator STOPs blinking, printing and hold down the chosen button on the HomeLink device for a full 5 seconds -  then release. (Ignore the HomeLink transmitter indicator during those 5 seconds.)

3. Confirm that the HomeLink device picked up the manual from the remote by pressing the chosen button on the HomeLink device.  The operator head LEDs should calorie-free in response.  If the operator LEDs low-cal, go on to the adjacent steps.  If after holding down the HomeLink device push for 5 seconds or longer, the LEDs on the head practise not light, echo from footstep i in this section until the operator LED lights blink in response to the HomeLink device button press.

Program the HomeLink Device to the Genie Garage Door Opener :

​

1. Locate either a foursquare PROGRAM button (PRGM) or round LEARN CODE button on the opener (ceiling). The location could be anywhere on the encompass of the opener or under a lens depending on the model.

2. Put opener into programming mode - the openers programming window will time out after xxx seconds:

   • PRGM button - press and agree downward until the LED turns blue, then release. Imperial LED begins flashing.​

   • Larn CODE push – press and hold down until the red LED starts flashing, so release.

3. ​Press and hold downwardly the HomeLink button for 2 full seconds - then release.  Press and hold down the called HomeLink button once more for 2 full seconds – then release.  Continue this process until the opener operates.  During this time, LEDs on the HomeLink device continue to blink and somewhen change to solid (opener should exist moving past and then).​

If y'all take these remotes, delight follow the instructions below :

Either of these remotes with a software revision of lower than (but non equal to) 2.03.  Software revisions tin be found on the back of these remotes under the visor clip.

Software Version

LED Locations

Preparing the Remote:

​

​

1. Choose a push button on the remote that you will use to train the HomeLink device.

   • If the LED on the transmitter lights Cerise, proceed to step 2.​ ​

   • If the LED on the transmitter lights Greenish – perform the following steps:

     1. Press and hold down this button for approximately 10 seconds or until BOTH A Carmine AND A GREEN LED light on the remote – then release the push. ​

     2. Immediately press the same button again chop-chop 2 times.

     3. Printing the aforementioned button once more – the ONLY LED that should lite is a Cherry ane.  If a Green LED lights, repeat this process again until the merely LED that lights at the end of step 1 is red.
        

2. Continue with pace i under "Train HomeLink device to the Remote" section above.

If yous demand to clear out your HomeLink device:

Notation:  If at any fourth dimension you need to start over completely, this process will remove all previously programmed garage door openers from the HomeLink device.

1. Press and hold down the starting time and third buttons on the HomeLink device until the indicator blinks slow at first and so fast for xx seconds – then release both buttons.​

​

Source: https://www.geniecompany.com/homelink-programming

Share this post